Universal Dimmer Module
EPM-DM3D
The universal dimmer module EPM-DM3D is designed to control
lighting loads. The module can operate in three-channel, twochannel
and one-channel modes. The device supports dimming of both forward (leading edge) and reverse phase (trailing edge) type loads.
The control, data exchange and configuration are all handled via TCP/IP protocol.
Universal Dimmer Module
EPM-DM6D
The universal dimmer module EPM-DM6D is designed to control LED lighting loads as well as incandescent and halogen loads.
The module operates in six-channel mode and can be configured to five-channel and four-channel modes.
The device supports dimming type of both leading edge and trailing edge modes and non-dim mode.
The control, data exchange and configuration are all handled via TCP/IP protocol.
Power Relay Module
EPM-RL6D
The Highcross EPM-RL6D is a module designed to switch lighting,
motors and other high voltage loads via relays.
The module features digital inputs allowing to control outputs via
standard buttons or switches without an external control system.
LED control Module
ECM-LD4D
ECM-LD4D module is designed to control brightness of LED strips. The module is compact and uses 1kHz PWM
to constant voltage lighting control and has two versions to control up to 10A/30VDC or 5A/48VDC
load for every channel. The outputs can be combined to increase the output power up to 20A, 30A
and 40A @ 30VDC.
LED control Module
ECM-LD9D
ECM-LD9D module is designed to control brightness of up to 9 monocolor LED strips or 3 RGB LED strips or their combinatios. The costeffective module uses 1kHz PWM to constant voltage
lighting control and has two versions to control up to 10A/30VDC or 5A/48VDC load for every channel.
Some or all outputs can be combined to increase the output power up from 20A up to 75A @ 30VDC.
Control module for curtains, shutters and screens
EPM-BS3D
EPM-BS3D is a motor control module designed to provide control of bidirectional motors for drapes,
shades and skylights as well as projection screens, lifts and gates via mutually exclusive high voltage relays. The module features digital inputs allowing motor control via standard buttons without an external control system.
The device switches channels off automatically after individual channel's timeout.
LED Lighting Driver
PWM-DMX3B
Thanks to the use o the DMX512 protocol, this three-channel driver is convenient to use to control
LED strips with an individual power level for each channel and is a convenient solution when placing power
supplies at the place of installation of the strip.
LED Lighting Driver
PWM-AI3B
The device is controlled via the generally accepted 0-10V interface,
which makes it easy to integrate LED lamps and strips into a single
control system with separate brightness control for each channel.
Can be mounted in close proximity to luminaires and tapes or power supplies.
Digital Temperature Sensor Module
ECM-DTS16D
The digital temperature sensor module ECM-DTS16D is designed
to receive temperature data from digital temperature sensors.
Universal Thermostat Module
ECM-UTM4D
The Highcross ECM-UTM4D is an electronic universal 3-channel
thermostat module designed to control of heating or cooling systems.
The module has three built-in thermostats, three power relays,
four analog inputs for temperature sensors, three pairs of digital
inputs for priority dry-contact control from window-contact or etc.
Multisensor
HCB-SENSOR
The multisensor is designed to measure and transmit information from digital sensors of air temperature and humidity, illumination,
pressure and air quality.
Infrared Control Module
ECM-IR4B
ECM-IR4B is a universal multifunctional IR-control module, designed to control audio / video systems, air conditioners and any other IR-controlled appliances. The module has intelligent IR-learning to parse and analyse unique and repeating sequences.
RS232/RS485/DMX512 Ports Module
ECM-RS2D
The ECM-RS2D module is designed to control any devices with
RS232/RS485 interface as well as be DMX512 controller.
The module is a bidirectional gateway between physical interface
RS232/RS485 and Ethernet network and supports multiple TCP/
IP connections for each serial port.
RS232/RS485/DMX512 Ports Module
ECM-RS2B
The ECM-RS2B module is designed to control any devices with RS232/RS485 interface as well as be DMX512 controller.
The module is a bidirectional gateway between physical interface RS232/RS485 and Ethernet network and supports multiple TCP/IP connections for each serial port.
Digital Input/Output Module
ECM-IO16D
The Highcross ECM-IO16D module has sixteen digital input/output
channels. Digital inputs can be configured as normally-open or normally-close
input type. Digital outputs are implemented as open collector.
Control of device is produced by TCP/IP network. Built-in web-interface is used to device configuration.
The module is designed to be installed on a standard 35 mm DIN rail.
Low-Voltage Relay Module
ECM-RL12LVD
The Highcross ECM-RL12LVD module has twelve low-voltage low-current signal relay outputs for providing a potential-free output
contact.
Analog Output Module
ECM-AO4D
The analog output module ECM-AO4D is designed to control equipment via analog 0-10V interface.
The module has open collector terminals to control the external
power relays or as an additional source of ON and OFF signal.
The control, data exchange and configuration are all handled via TCP/IP protocol.
Every channel has a pair of digital inputs for manual control and supports one-button and two-button control modes.
Bus controller
EBM-BUS2D
EBM-BUS2D is designed for bi-directional HCBus communication from Highcross bus devices (eg bus switches) to Ethernet
and vice versa. Supports connection of up to two Highcross buses with a length of each up to 800 m.
Bus switch
HCB-PBS2LCD / RGB
The bus switch is designed to transmit information about the state of the buttons, current values
of temperature and humidity, illumination, allows
you to change the color of the backlight of the button status indicators by commands,
display textual information on the OLED display.
The switch is connected to the HCBus.
Multisensor
HCB-SENSOR
The multisensor is designed to measure and transmit information from digital sensors of air temperature and humidity, illumination,
pressure and air quality.The device uses a digital bus HCBus and connects to EBM-BUS2D controller that communicates with external controllers via Ethernet.
Complex solution
MediaBANK
What is the MediaBANK?
The MediaBANK is a special computer that can store thousands of hours of music, tens of thousands of photos,
and alarge number of movies. And most importantly, he knows how to broadcast this data simultaneously for several
zones. The media server can work in combination with the Multiroom system or independently participate in the Smart
Home system.